10/27/2021 0 Comments Upgrade Usb 3.0 To 3.1 For Mac Pro
Thanks in advance.Add Two USB-C 10Gbps Ports to Mac Pro, Windows, and Linux Computers with PCIe Slots. Mac Mini is a bit cheaper but since I will be upgrading RAM it is the same price. I have to choose and buy one this week. Mac Mini 2012 2.3 GHz Quad-Core i7 4 GB RAM (will upgrade it to 10 or 16 instantly) SSD 128GB. MacBook Pro mid 2012 2,9 GHz dual-core i7 8 GB Ram 1000 HDD (will put SSD that is already laying around) or.Add SuperSpeed+ USB Technology. Low-profile Dual-port With 15W Power Per Port. For more information, read Total Nightmare: USB-C and Thunderbolt 3!Compared to the original Mac Pro that it replaced, the 'Early 2008' Mac Pro uses a more advanced architecture with faster and more efficient processors with larger level 2 caches, a more advanced vector engine, faster frontside buses (1.6 GHz instead of 1.33 GHz), faster memory (800 MHz instead of 667 MHz), support for optional faster Serial Attached SCSI drives (with the installation of the Mac Pro RAID PCI Express 3.0 Card. These things can do quite a lot but you must be careful about what cables and accessories you buy! Revisiting USB Type-C and Thunderbolt 3 I wrote a very popular article on this topic.
![]() Usb 3.0 To 3.1 Pro Upgrade It ToIf your monitor supports DisplayPort, it’s best to connect directly to it using a USB-C Alternate Mode to DisplayPort cable rather than using a dock or adapter. DisplayPort VideoDisplayPort is a bit more advanced than HDMI at this point, even though the MacBook Pro only supports DisplayPort version 1.2. I’ve got a few of these.Therefore, your expenditure for an additional power adapter will be $87 to $110.79, depending on what you buy. If you want one of those, I recommend buying the bulk-packaged cable from OWC for just $6.79. It supports fast data transfer and a full 100 Watts of charging for just $18 or $25.Also, the Power Adapter no longer comes with the 1.8 Meter extension cable. Especially for 15″ MacBook Pro owners, since it won’t pass more than 60 Watts. But the reviews are really, really bad, so I wouldn’t spend $69 on that. I can confirm that the Monoprice adapter below does not work reliably with the Dell S2715H or P2715Q displays at least. It’s best to try to use DisplayPort if possible since that’s been much more reliable.If you have a monitor that only supports HDMI, you might be tempted to buy the Apple USB-C Digital AV Multiport Adapter. HDMI VideoWarning: Reviewers say that HDMI over USB-C Alt Mode has been flaky with the new MacBook Pro. I have had no issues at all with the Monoprice 12908 cable pictured above. This USB-C to DisplayPort cable from Monoprice ought to be the best way to connect to a DisplayPort monitorYou could also try the Monoprice Select Series USB-C to DisplayPort adapter for just $15.Update: I have purchased both of these and can confirm that they work just fine with my monitor, a Dell P2715Q, pushing 3840 x 2160 at 60 Hz. Xee for macDefinitely do not buy “2.0” cables, since they don’t even have all the wires connected inside! ThunderboltIf you have existing Thunderbolt peripherals, you’re in luck! Your new late-2016 MacBook Pro should be fully compatible with them. It’s actually cheaper than the Monoprice “Select Series” equivalent, though their shorter palette cable is only $15. Do not buy the 2.0-only USB-C cable from Apple! Instead, get a few Monoprice palette cables for only $15.Don’t waste your money on cheaper cables, since many can’t handle the data or power that USB-C is capable of delivering. Frankly, the official Apple USB-C to USB-C cable, at just $19, is a great choice. Do not buy an HDMI adapter until there’s news of better support! USB-C PeripheralsYou should have a few good-quality USB-C cables around in case you need one. One was not recognized at all and neither displayed any video. This cheap $15 Monoprice adapter ought to extract native HDMI from the USB-C port but it does not work!Update: I purchased the Monoprice 13235 and it did not work with either of the HDMI monitors I tried. But remember – you must use a Thunderbolt 3 cable, not just any old USB-C cable! Apple likes the Belkin cables, but the StarTech cables are cheaper and I’ve had great luck with their previous-generation Thunderbolt cables.Warning: Thunderbolt 3 peripherals using first-generation Texas Instruments Thunderbolt 3 controllers (TPS65982) are apparently not supported by the MacBook Pro! Do not buy any TB3 peripheral unless you see that it has been tested with the MacBook Pro! Ethernet I recommend buying the Belkin USB-C to Gigabit Ethernet adapter from Apple for $26Most existing USB 3 and USB-C Ethernet adapters ought to work with the MacBook Pro. However, note that it does not support DisplayPort video, despite having the same connector.As Thunderbolt 3 peripherals begin to appear, your late-2016 MacBook Pro should work with most of them. It’s worth getting it if you have any older Thunderbolt peripherals. Theoretically, you should be able to stack the Apple Thunderbolt 3 to Thunderbolt 2 adapter and the Apple Thunderbolt to FireWire adapter, but this isn’t guaranteed to work. FireWireThere really isn’t a great FireWire solution for the MacBook Pro right now. I also used the Apple Thunderbolt adapter with Apple’s converter and a USB 3 Ethernet adapter which worked but required a driver install. Furthermore, I suggest buying it from Apple since they have reduced the price to just $26 through the end of the year!Update: I purchased the Belkin adapter from the Apple Store and it works perfectly without any driver installs. This is a native USB-C device and should work perfectly. Existing USB 3.0 PeripheralsI’m still a little nervous about “native” USB-C hubs and docks. Stick with a converted USB 3 reader for now, or just plug your camera into your computer with an appropriate USB-C to USB cable. And it’s only $29 from Apple right now.Update: Reports say that the SanDisk reader doesn’t work well. If you want a native USB-C reader, I suggest buying the one Apple suggests, the SanDisk Extreme Pro reader. SD Cards So much less elegant for photographers than the old MacBook Pro…Most USB SD card readers should work with an adapter. I’ll blog about it when it’s released (tentatively February 2017).Update: I can confirm that the Apple Thunderbolt 3 to Thunderbolt 2 converter does work with the Apple Thunderbolt FireWire adapter. Instead, I bought a few USB-C to USB 3.0 adapters and will be using my existing collection of USB 3.0 devices.I like the idea of the little integrated USB-C to 3.0 USB-A adapters, but the initial reviews have been poor. I bought the Monoprice Select Series USB 3.
0 Comments
Leave a Reply. |
AuthorFrank ArchivesCategories |